Epoch Batteries 48V 100Ah V2 Elite Series LiFePO4 Battery (5.12kWh)
Epoch Batteries' product pageThe Epoch Batteries 48V 100Ah V2 Elite Series LiFePO4 Battery (5.12kWh) is a battery pack with a capacity of 100Ah (0.5C, 25°C), LiFePO4 / lithium iron phosphate cells, a continuous discharge of 150 A and a peak of 300 A for 30 seconds.
Last updated: 17 November 2026
What this device draws
- Power drawn at full throttle
- 20mA powered on; 200µA powered off
Row from the maker’s page: “Self-consumption” | “20mA powered on; 200µA powered off”
Source: epochbatteries.com/products/48v-100ah-v2-elite-lifepo4-battery
Battery and charging
- Capacity (amp-hours)
- 100Ah (0.5C, 25°C)
- Maximum charge voltage
- 58.4V (3.65V per cell)
- Temperature compensation
- Disabled (0 mV/°C)
- Energy
- Sources disagree
5.12kWh / 5,120Wh
“Energy capacity 5.12kWh / 5,120Wh”
Source: epochbatteries.com/products/48v-100ah-v2-elite-lifepo4-battery
5,120Wh
Row from the maker’s page: “Energy capacity” | “5.12kWh / 5,120Wh”
Source: epochbatteries.com/products/48v-100ah-v2-elite-lifepo4-battery
- Voltage
- 51.2V (3.2V per cell)
- Chemistry
- LiFePO4 / lithium iron phosphate
- Rated charge cycles
- 3,500+ cycles to 70% remaining capacity (25°C, 0.5C charge, 1C discharge)
- Case material
- ABS and PC blend (UL94 V-0)
- Cell arrangement
- 16S1P (100Ah cells)
- Battery type
- Heated Bluetooth LiFePO4 deep-cycle battery with Victron communication
- Nominal capacity
100Ah (0.5C, 25°C)
“Nominal capacity 100Ah (0.5C, 25°C)”
Source: epochbatteries.com/products/48v-100ah-v2-elite-lifepo4-battery
100Ah
“Victron Comms Capacity: 100Ah”
Source: epochbatteries.com/products/48v-100ah-v2-elite-lifepo4-battery
- Fuse rating
270A rated (UL 60691, TEX150-R1N-XBZ)
Row from the maker’s page: “Internal fuse” | “270A rated (UL 60691, TEX150-R1N-XBZ); 1,200A transient overload for 3 seconds”
Source: epochbatteries.com/products/48v-100ah-v2-elite-lifepo4-battery
270A internal fuse (UL 60691)
“Advanced Smart BMS & Certifications: Over/under-voltage, overcurrent, short-circuit and high/low temperature protection, and a 270A internal fuse (UL 60691). UL 1642, UL 9540A and IEC 62619:2022 cells; CE and RoHS. The internal fuse does not replace system protection: install a DC-rated fuse or breaker close to the battery positive.”
Source: epochbatteries.com/products/48v-100ah-v2-elite-lifepo4-battery
- Maximum continuous discharge
- 150A (up to 20 minutes at 150A; not for cycling)
- Peak discharge
- 300A for 30 seconds
- Series and parallel limit
- Max 16 batteries in parallel; set the DIP switches for the bank
- Highest charge current it will take
- 100A
- Maximum charge current, as the maker labels it
- 300A for 5 seconds
- BMS charge cut-off voltage
- 58.4V
- Charging voltage
- 56.8V
- Float voltage
- 54.0V
- Working voltage range
- 40.0V – 58.4V
- How fast it loses charge sitting idle
- ≤3% per month (100% SOC, 25°C)
“Nominal capacity 100Ah (0.5C, 25°C)”
Source: epochbatteries.com/products/48v-100ah-v2-elite-lifepo4-battery
Row from the maker’s page: “Maximum voltage” | “58.4V (3.65V per cell)”
Source: epochbatteries.com/products/48v-100ah-v2-elite-lifepo4-battery
Row from the maker’s page: “Temperature compensation” | “Disabled (0 mV/°C)”
Source: epochbatteries.com/products/48v-100ah-v2-elite-lifepo4-battery
“Nominal voltage 51.2V (3.2V per cell)”
Source: epochbatteries.com/products/48v-100ah-v2-elite-lifepo4-battery
“Chemistry LiFePO4 / lithium iron phosphate”
Source: epochbatteries.com/products/48v-100ah-v2-elite-lifepo4-battery
“Cycle life 3,500+ cycles to 70% remaining capacity (25°C, 0.5C charge, 1C discharge)”
Source: epochbatteries.com/products/48v-100ah-v2-elite-lifepo4-battery
“Case material ABS and PC blend (UL94 V-0)”
Source: epochbatteries.com/products/48v-100ah-v2-elite-lifepo4-battery
“Cell configuration 16S1P (100Ah cells)”
Source: epochbatteries.com/products/48v-100ah-v2-elite-lifepo4-battery
Row from the maker’s page: “Battery type” | “Heated Bluetooth LiFePO4 deep-cycle battery with Victron communication”
Source: epochbatteries.com/products/48v-100ah-v2-elite-lifepo4-battery
“Max continuous discharge 150A (up to 20 minutes at 150A; not for cycling)”
Source: epochbatteries.com/products/48v-100ah-v2-elite-lifepo4-battery
“Peak discharge 300A for 30 seconds”
Source: epochbatteries.com/products/48v-100ah-v2-elite-lifepo4-battery
Row from the maker’s page: “Parallel connections” | “Max 16 batteries in parallel; set the DIP switches for the bank”
Source: epochbatteries.com/products/48v-100ah-v2-elite-lifepo4-battery
“Max continuous charge current 100A”
Source: epochbatteries.com/products/48v-100ah-v2-elite-lifepo4-battery
“Elite Performance Specifications: 150A maximum continuous discharge, about 7,680W DC at 51.2V before inverter losses, for up to 20 minutes at 150A (not for cycling), and 300A for 30 seconds for surges. 100A maximum continuous charge, with up to 300A for 5 seconds. If an inverter's continuous DC input can exceed 150A, add batteries in parallel.”
Source: epochbatteries.com/products/48v-100ah-v2-elite-lifepo4-battery
Row from the maker’s page: “Max short-duration charge current” | “300A for 5 seconds”
Source: epochbatteries.com/products/48v-100ah-v2-elite-lifepo4-battery
Row from the maker’s page: “BMS high-voltage cutoff” | “58.4V”
Source: epochbatteries.com/products/48v-100ah-v2-elite-lifepo4-battery
Row from the maker’s page: “Absorption voltage” | “56.8V”
Source: epochbatteries.com/products/48v-100ah-v2-elite-lifepo4-battery
“Absorption time At least 15 minutes per battery in the bank Float voltage 54.0V”
Source: epochbatteries.com/products/48v-100ah-v2-elite-lifepo4-battery
“Operating voltage range 40.0V – 58.4V”
Source: epochbatteries.com/products/48v-100ah-v2-elite-lifepo4-battery
“Self-discharge ≤3% per month (100% SOC, 25°C)”
Source: epochbatteries.com/products/48v-100ah-v2-elite-lifepo4-battery
Battery care and safety
- Ingress protection
IP67: dust-tight; temporary immersion to 1 m for 30 minutes. Not rated for water jets, pressure washing or continuous submersion
“Enclosure protection IP67: dust-tight; temporary immersion to 1 m for 30 minutes. Not rated for water jets, pressure washing or continuous submersion”
Source: epochbatteries.com/products/48v-100ah-v2-elite-lifepo4-battery
IP67 Rated Enclosure: Dust-tight and protected against temporary immersion in up to 1m of water for 30 minutes. It is not rated for water jets, pressure washing or continuous submersion
“IP67 Rated Enclosure: Dust-tight and protected against temporary immersion in up to 1m of water for 30 minutes. It is not rated for water jets, pressure washing or continuous submersion: install it where it stays dry in normal use, with all harness connectors fully seated.”
Source: epochbatteries.com/products/48v-100ah-v2-elite-lifepo4-battery
- Temperature the cells themselves charge at
- 0°C to 55°C / 32°F to 131°F
- What the battery management system protects against
- Sources disagree
Overcharge, over-discharge, over-current, short circuit, high/low temperature disconnects
Row from the maker’s page: “Smart BMS protection” | “Overcharge, over-discharge, over-current, short circuit, high/low temperature disconnects”
Source: epochbatteries.com/products/48v-100ah-v2-elite-lifepo4-battery
Over/under-voltage, overcurrent, short-circuit and high/low temperature protection
“Advanced Smart BMS & Certifications: Over/under-voltage, overcurrent, short-circuit and high/low temperature protection, and a 270A internal fuse (UL 60691). UL 1642, UL 9540A and IEC 62619:2022 cells; CE and RoHS. The internal fuse does not replace system protection: install a DC-rated fuse or breaker close to the battery positive.”
Source: epochbatteries.com/products/48v-100ah-v2-elite-lifepo4-battery
- Temperatures it may be charged in
- -30°C to 55°C / -22°F to 131°F ambient, with self-heating
- Temperatures it may be run in
-20°C to 55°C / -4°F to 131°F
“Discharge temperature range -20°C to 55°C / -4°F to 131°F”
Source: epochbatteries.com/products/48v-100ah-v2-elite-lifepo4-battery
Discharge works down to -20°C (-4°F)
“HEATED For Extreme Climates: LiFePO4 cells must not be charged below 0°C (32°F). When a charger is connected and the cells are too cold, the BMS holds off charging while the internal heater, powered by the charge source, warms them; charging resumes at 5°C (41°F). With self-heating, charging is supported from -30°C (-22°F) ambient. Discharge works down to -20°C (-4°F).”
Source: epochbatteries.com/products/48v-100ah-v2-elite-lifepo4-battery
- Temperatures it may be stored in
- 0°C to 35°C / 32°F to 95°F
- Internal heating
- Yes
- Heating built into the battery
- Yes — charging stops at 0°C and resumes at 5°C (cell temperature) while the heater, powered by the charge source, warms the cells
“Cell charge temperature range 0°C to 55°C / 32°F to 131°F”
Source: epochbatteries.com/products/48v-100ah-v2-elite-lifepo4-battery
“Charge temperature range -30°C to 55°C / -22°F to 131°F ambient, with self-heating”
Source: epochbatteries.com/products/48v-100ah-v2-elite-lifepo4-battery
Row from the maker’s page: “Storage temperature, up to 1 year” | “0°C to 35°C / 32°F to 95°F”
Source: epochbatteries.com/products/48v-100ah-v2-elite-lifepo4-battery
Row from the maker’s page: “Internal heating” | “Yes”
Source: epochbatteries.com/products/48v-100ah-v2-elite-lifepo4-battery
Row from the maker’s page: “Self-heating” | “Yes — charging stops at 0°C and resumes at 5°C (cell temperature) while the heater, powered by the charge source, warms the cells”
Source: epochbatteries.com/products/48v-100ah-v2-elite-lifepo4-battery
Size and fit
- Weight
97 lb / approx. 44 kg
“Weight 97 lb / approx. 44 kg”
Source: epochbatteries.com/products/48v-100ah-v2-elite-lifepo4-battery
approx. 44 kg
Row from the maker’s page: “Weight” | “97 lb / approx. 44 kg”
Source: epochbatteries.com/products/48v-100ah-v2-elite-lifepo4-battery
97 lb (approx. 44 kg)
“Dimensions & Fit: 20.86" L x 8.65" W x 12.06" H (529.8 x 219.8 x 306.3 mm; the height includes the terminal posts), 97 lb (approx. 44 kg). Install it upright. Replacing a Group 8D lead-acid battery? Confirm tray fit, hold-down and lid clearance against these dimensions first; the optional Epoch V2 & V2-T Mounting Hardware (8D battery bracket, sold separately) fastens to the six M8 nuts on the case.”
Source: epochbatteries.com/products/48v-100ah-v2-elite-lifepo4-battery
- Overall height
- 12.06 in
- Total length
- 20.86 in
- Total width
- 8.65 in
- Overall dimensions
20.86 in L × 8.65 in W × 12.06 in H (529.8 × 219.8 × 306.3 mm; height including terminal posts)
“Dimensions 20.86 in L × 8.65 in W × 12.06 in H (529.8 × 219.8 × 306.3 mm; height including terminal posts)”
Source: epochbatteries.com/products/48v-100ah-v2-elite-lifepo4-battery
20.86" L x 8.65" W x 12.06" H (529.8 x 219.8 x 306.3 mm; the height includes the terminal posts)
“Dimensions & Fit: 20.86" L x 8.65" W x 12.06" H (529.8 x 219.8 x 306.3 mm; the height includes the terminal posts), 97 lb (approx. 44 kg). Install it upright. Replacing a Group 8D lead-acid battery? Confirm tray fit, hold-down and lid clearance against these dimensions first; the optional Epoch V2 & V2-T Mounting Hardware (8D battery bracket, sold separately) fastens to the six M8 nuts on the case.”
Source: epochbatteries.com/products/48v-100ah-v2-elite-lifepo4-battery
- Terminals
- M8 threaded; 8–12 N·m (71–106 lbf·in)
- How it mounts
- Upright; six M8 nuts for the optional Epoch V2 & V2-T Mounting Hardware (8D battery bracket, sold separately), 125 mm (4.92 in) spacing
- Series and parallel connection
- No series connections; native 48V battery
Row from the maker’s page: “Height” | “12.06 in”
Source: epochbatteries.com/products/48v-100ah-v2-elite-lifepo4-battery
Row from the maker’s page: “Length” | “20.86 in”
Source: epochbatteries.com/products/48v-100ah-v2-elite-lifepo4-battery
Row from the maker’s page: “Width” | “8.65 in”
Source: epochbatteries.com/products/48v-100ah-v2-elite-lifepo4-battery
“Terminals M8 threaded; 8–12 N·m (71–106 lbf·in)”
Source: epochbatteries.com/products/48v-100ah-v2-elite-lifepo4-battery
Row from the maker’s page: “Mounting” | “Upright; six M8 nuts for the optional Epoch V2 & V2-T Mounting Hardware (8D battery bracket, sold separately), 125 mm (4.92 in) spacing”
Source: epochbatteries.com/products/48v-100ah-v2-elite-lifepo4-battery
Row from the maker’s page: “Series connections” | “No series connections; native 48V battery”
Source: epochbatteries.com/products/48v-100ah-v2-elite-lifepo4-battery
Compatibility
- How it talks to the battery
- Sources disagree
Yes — CAN bus at 500 kbit/s to compatible Victron GX devices (BMS-CAN or VE.Can port)
Row from the maker’s page: “Victron communication” | “Yes — CAN bus at 500 kbit/s to compatible Victron GX devices (BMS-CAN or VE.Can port)”
Source: epochbatteries.com/products/48v-100ah-v2-elite-lifepo4-battery
CAN bus at 500 kbit/s
“Native VICTRON Communications: CAN bus at 500 kbit/s to a compatible Victron GX device (Cerbo GX, Ekrano GX or Cerbo GX Mk2). The battery reports its status and charge limits, and with DVCC on it sets the charge voltage and current limits of Victron chargers. The communication harness is included; set the DIP switches and GX settings per the manual.”
Source: epochbatteries.com/products/48v-100ah-v2-elite-lifepo4-battery
Identity
- Series name
- V2 Elite Series
- Sales model
- 48V 100Ah V2 Elite Series LiFePO4 Battery (5.12kWh)
- What the wattage in the name means
- 51.2V × 150A = 7,680W DC, before inverter losses (up to 20 minutes)
Row from the maker’s page: “Series” | “V2 Elite Series”
Source: epochbatteries.com/products/48v-100ah-v2-elite-lifepo4-battery
“48V 100Ah V2 Elite Series LiFePO4 Battery (5.12kWh)”
Source: epochbatteries.com/products/48v-100ah-v2-elite-lifepo4-battery
Row from the maker’s page: “Theoretical continuous DC output” | “51.2V × 150A = 7,680W DC, before inverter losses (up to 20 minutes)”
Source: epochbatteries.com/products/48v-100ah-v2-elite-lifepo4-battery
Buying and owning it
- How charged it arrives
- 30% ± 3%; charge fully before first use
Row from the maker’s page: “State of charge at shipment” | “30% ± 3%; charge fully before first use”
Source: epochbatteries.com/products/48v-100ah-v2-elite-lifepo4-battery
Other findings
- Bluetooth
- Sources disagree
Yes — Bluetooth 4.0 through the included battery gauge; Epoch Li-Ion app (iOS and Android)
Row from the maker’s page: “Bluetooth” | “Yes — Bluetooth 4.0 through the included battery gauge; Epoch Li-Ion app (iOS and Android)”
Source: epochbatteries.com/products/48v-100ah-v2-elite-lifepo4-battery
Bluetooth 4.0 through the included battery gauge
“BLUETOOTH Battery Intelligence: Bluetooth 4.0 through the included battery gauge. The Epoch Li-Ion app (iOS and Android) shows state of charge, voltage, current, cell voltages, temperatures, history and warnings, and installs firmware updates over the air. The battery has a power button, and a mountable ON/OFF switch and the mountable battery gauge are included.”
Source: epochbatteries.com/products/48v-100ah-v2-elite-lifepo4-battery
Sources
- 48V 100Ah V2 Elite LiFePO4 Battery (5.12kWh) | EpochArchived document
Source: epochbatteries.com/products/48v-100ah-v2-elite-lifepo4-battery
Retrieved November 2, 2026